The continued research into the action of the
waveplates brings forth many known scientific rules which I will begin to
address in these writings.
Also, Victor S. especially noted that the waveplates be fabricated out of
copper alloy material, with a silver coated anodizing. The egg shaped
housing is also fabricated out of copper. So, of course the logical question
is why. This will also be addressed in these writings.
To begin with, as you start the spin of the waveplates, you will create a
vacuum of air to be sucked across the plates toward the outside diameter.
This will now start a rotation of normal air molecules circulating
counterclockwise around the inside of the enclosed housing. Now anytime you
enclose circulating air mass in an enclosed chamber, the normal air friction
between the air molecules and the housing will create heat. The
recirculating air, spinning into itself creates no friction, so it is the
subsequent impact that creates this heat. Heat always creates pressure. So
now we have a building of pressure also inside the egg housing. The normal
resistant air has to come from somewhere so a velocity cone is assembled
into the center of the housing to direct incoming cool air into the spinning
plates. See DIAGRAM 1. Now the air has to have an escape method so at
the top of the egg housing and attached to the center mounted velocity cone
is an exhaust turbine that is connected via the velocity cone back to the
waveplates. As the heated air begins to build pressure, this pressure is
naturally funneled into the exhaust turbine. The resulting pressure is now
used to add velocity back down the cone into the waveplates. Now, the
resulting airflow inside begins to increase in temperature to about 300-500
degrees F. within a few minutes.
This is where things begin to get interesting. The press formed plates after
assembly create a waveform intersticial space. Both plates are maintained at
a distance at the inside diameter and decrease in a uniformed distance all
the way to the outside diameter. Now the exact spacing is unknown at this
time. The slits cut into the upper plates let the outside circulating air
get sucked into the area between the waveplates. Rotational velocity creates
the suction or vacuum. So after a period of time we now have normal
resistant air in the chamber getting very hot, and this air is being sucked
right back into the waveplates. Lets take normal water and cool it to a
crisp 42 degrees and now inject this cooled water into the center of the
intersticial area. We will now create a normal thunderstorm to happen which
I will denote as a natural endothermic reaction. Science describes an
Endothermic Reaction to be: “Cold tries to take energy away from hot and
creates an expansion of pressure”. Victor talks about this same thing on
page 87-88, “Heat is first generated thru friction. The heat is
immediately absorbed by the water and in the process a physical vacuum is
created. Which then gives rise to the emergence of inner atomic rays. Due to
the absorbed heat, the free dissolved oxygen still present in the water
becomes aggressive owing to the present of the vacuum. Through the encounter
of the mutually opposed, contra-directionally propagated, excited rays, the
precondition for the marriage is created, the child of this union is
organic, or cold light.
Now, not a lot of water need be injected to cause this to happen and if this
water is atomized at the injection point, a better reaction is created. In
between the waveplates we now have created a pressurized state to develop on
top of the rotational vacuum. Whereby creating the repulsion state to come
about.
Lets look at a normal garden hose. Usually a garden hose has about 40 lbs of
pressure behind it to flow the water. By installing a squeeze nozzle at the
end, the pressure in the hose builds, and when you squeeze the nozzle and
inject all that pressure thru a very small orifice, a stream of water up to
20 feet is ejected. Now lets put this same analogy into the waveplates. We
have produced now a pressure inside the waveplates that is vacuumed to the
outside diameter by rotational velocity and now all is required is a small
orifice around the outside diameter to create the repulsion energy. As the
rotation increases, pressure increases, and when the repulsion effect
happens the air molecules create their expansion on exiting the orifice at
the outside diameter subsequently ejecting against the turbine blades which
are cocked at a 30 degree angle. This results in a increase of rotation of
the waveplates along with the expansion of air pressure up to 115 times. The
ejection of the repulsed air will now also increase the pressure inside the
egg housing increasing the pressure against the exhaust blades creating even
more spin back into the waveplates. We now have created a living breathing
motor, just as V.S. has talked about. By siphoning off the rotation of the
center shaft and reducing the rpm thru a reduction drive now creates H.P.
Rotational control can also be done by creating a mechanical devise to
control the turbine blade angle to increase or decrease spin, Much like an
adjustable pitch propeller on an aircraft.
But every engine will produce a by product from a reaction. Combustion
engines that burn gasoline and oxygen produce carbon monoxide. The repulsion
engine will produce a hydrogen byproduct, after separating the hydrogen
molecule from the oxygen. But now this hydrogen molecule is being
recirculated back thru the waveplates along with the normal resistant air
and we may now create sub-atomic hydrogen. So now our calculations are
changed from normal resistant air molecules to heated hydrogen ionized gas
circulating around the egg chamber. A completely different set of
temp/pressure/ vacuum equations are justified because of the now changing
gas product.
Electrical emissions are also a by-product of this wonderful device. Since
the waveplates are isolated away from the center shaft, a positive charge of
electricity is going to build up on the waveplates. This is also
explained by “When the hydrogen atom is caused to impact a copper atom at a
high rate of acceleration, then the copper atom will capture the last
remaining electron of the hydrogen atom”. This now creates the basis for
ionized hydrogen or sub-atomic hydrogen.
A Hydrogen Ion: Having a kinetic energy of 1 electron volt, would have a
velocity of 10.85 x 10(3) m/sec or nearly 6.1 miles per second (32,208
ft/sec. or 21,954 mph.). As long as ionized hydrogen does not combine with
other gases like 02 it will be H or monatomic hydrogen. It will occupy twice
the space of H2 and have twice the lifting power. (.014) Hydrogen gas on the
other hand has a average molecular speed of 1693 m/sec or 5554.73 ft/sec @32
degrees F. or 0 degrees Centigrade. That is .07 lbs lift per cubic foot of
gas.
The blue hue effect seen outside the egg housing is the formation of
monatomic hydrogen which has lost its last remaining electron to the copper
waveplates. This again is known well in the circle of science. Most cases of
UFO sightings will talk about a humming noise or the blue hue noticed around
the top of the circular vehicles.
The waveplates have to be isolated away from the center shaft, because this
charge is not allowed to be grounded. Noticed, by more than one observer who
has been able to create this effect is the strong static lightning bolts
seen shooting out of the repulsion housing. These build up of charges can be
captured and manipulated to capacitors and Static/AC/DC transformers for
production into usable electrical current. This current can be used in
operation of the vehicle or used to process electrical energy for
residential use. Imagine running your repulsion system on the water supplied
to your house. Static electricity is also the basis for electronic force
fields.
V.S. wrote that on average, implosive forces are 127 times more powerful
than explosive forces. Tesla’s 12” multi bladed turbine produced a possible
125 hp while Schaubergers 12” waveplates produced 1250 hp. (10 times more)
Small implosion machines of 8” diameter rotating at 10,000 rpm. Can lift 57
tons and at 20,000 rpm. 228 tons.So a 18”
diameter should connect with repulsion energy at about 1500 rpm with an
outside diameter velocity of 14,130 ft/min. or a speed of 282.6 mph. A total
rpm range can easily exceed 10,000 rpm. So this could generate an enormous
lift range totally incomparable to anything in existence even today. Air
driven implosion machines specify air speeds of 124 mph. (124mph x 5280ft =
654720/60 min. = 10912/60 sec = 181.86 fps.
Wind velocity, must exceed this amount before repulsion happens. (pg. 134
fig.21) The greater the rpm, the more lift capability. So the 18” waveplate
rotating at 10,000 rpm has an outside velocity of 1570 fps. Exactly how much
lift capacity (suction), unknown. The actual volume of cubic feet of air
moving thru the repulsion unit is staggering.
Hydrogen, being a by-product of the repulsion unit does not destroy the
atmosphere like carbon monoxide. It actually enhances the environment.”
The aeriform substances transformed in the machine create very high grade
nitrogenous material which increases the vitality and germinating capacity
of the vegetation”. V.S. PG. 116 Energy Evolution
Wave Frequency’s
Wave frequencies are also emitted from the repulsion unit upon entering the
repulsion state. These frequencies are denoted to be in the 8 megahertz
range. Much has been found regarding this information and will write more on
this at a latter time.
Waveplate Technology
There are numerous ways of restructuring the waveplate system to cause many
forms of energy to come about. I will explain several of these that were
written in “The Energy Evolution” book.
- The process which I have explained above is the
injection of water to create hydrogen gas in order to create the upside
down tornado process. This leads to the low pressure area an subsequently
to the levitation theory.
- This waveplate forms, can also produce electrical
current. But if the pressure tongues are added to the top of the waves as
shown on pg. 192 & 193 a counter flow of air is produced and the
electrical content is magnified. This is again verified in pages 213
fig.37 Here you establish two contradicting flows of air against each
other at a high rpm. What you achieve here is a paramagnetic action in the
gas environment.
- If this particular form of waveplates is spun in
water, then the effect is the cleansing of dirty water to spring pure
drinking water. Pg 143
- Another possibility is to induce a man made
electrical current by a circular magnet wrapped by a coil of wire and
energized between the waveplate waves outside the intersticial area
whereby creating a magnetic thunderstorm within the inside of the plates.
This is spoke of on pg. 117 Vacuum Turbine
- Cold light can be achieved by rotating a set of
waveplates inside a vacuum tube to achieve the highest resistant velocity.
Whereby produces atmospheric space-light. A naturalesquely copied sunlight
as it were. See pg. 173 par. 3
CONCLUSION
There are lots of other goodies that can be added to the waveforms to create
other effects. I have only touched on a small part of this vast land of
energy. I have found many more theories of producing double or triple the
energy output, merely by assembling a second or third stage smaller diameter
plates on top of larger plates whereas the smaller plates achieve the energy
output as the plates reach higher rpm. The waveplates can be pressed into
other type forms to enhance electrical energies by the rotation of water
explained by V.S. in earlier methods. The mechanical assembly of complete
resistant spin of the waveplates thru magnetism and bearing less
applications further enhance the energy production. And I conclude on this
note. V.S. only injected water thru his waveplates but always talked about
injecting other chemicals. There is a whole periodical table of elements to
be explored by injecting certain combinations of fluids thru these
waveplates and exceeding their velocity into a recombining effect. This is a
complete open field of research. There is no telling what secrets might be
unearthed by mother nature. Other fluid combinations being subjected to the
4Th and 5th spatial dimensions of existence and their ultimate ur-genesis
transformations can generate new concepts of materials or energies not
previously know.
Sincerely
Kim A. Zorzi
C.E.O.
Ultralight America |
